GateMix™

Mix to the core

Homogenises the melt right at each gate: virgin/recycled polymers, colourants and additives. Same line, no capital request.

01 · What it is

GateMix™ at each gate

The problem

Holding quality is getting more expensive

  • ✕Quality: higher customer quality standards turn streaks and uneven shade into rejects
  • ✕Compliance: PPWR means more recycled content, so more variation to manage
  • ✕Cost: colourants and additives get overdosed to compensate, and costs rise
Two blue PET preforms: without GateMix™ with colourant streaks, with GateMix™ an even colour, and between them the GateMix™ insert, one per gate

Without GateMix™

With GateMix™

The solution

GateMix™: one insert at each gate, in your existing hot-runner nozzle

  • ✓Quality: an evenly mixed melt at each gate, so streaks and uneven shade disappear and rejects fall
  • ✓Compliance: compliant with rPET, so more recycled content stays under control
  • ✓Cost: at least 15% lower dosage of colourants and additives

02 · How it works

How it works

Colourants, additives, virgin and/or recycled content reach the nozzle unevenly mixed. Inside the nozzle, just before the gate, GateMix™ evens them out with three moves, repeated stage after stage:

  • 1
    Split
    The melt is divided into separate streams.
  • 2
    Squeeze
    Each stream is flattened into a thin layer.
  • 3
    Stack
    The layers are stacked back together.
  • ↻
    Repeat
    The three moves are repeated, multiplying the layers until they blend on their own at the gate.
Same cycle time
No additional heating
Same hot runner
Click the animation to enlarge it.
Animation of the melt inside the GateMix™ insert: grey and blue streams are split, squeezed and stacked until they leave evenly mixed

03 · What you gain

Three gains, one insert

Quality: fewer defects, less scrap

An evenly mixed melt at each gate, so streaks and uneven shade disappear: more good parts, fewer rejects. Validated in industrial production.

Compliance: validated with recycled content

Compliant with rPET, validated in industrial PET preform production with up to 100% recycled content. Further results under way.

Cost: lower dosage, no capital request

At least 15% lower dosage of colourants and additives. No capital request: the insert fits your existing hot runner.

04 · Your savings

Savings calculator

What would GateMix™ do on your line?

Enter a few figures about your line and see your saving and payback in two minutes.

GateMix™ Savings Calculator result on a tablet

05 · Proven in production

Use case: colourant masterbatch · PDG Plastiques

PET preforms with up to 100% recycled content

PDG Plastiques, a French preform maker that adopts new processing technology early, runs GateMix™ in ongoing industrial production to take its quality further. Colourants: blue, green, yellow and white. Same tool, same material, same settings: a reference without GateMix™ first, then with GateMix™.

What we checked
Without GateMix™
With GateMix™
Colourant dosage
✕Standard dosage
✓At least 15% lower dosage
Streaks, waves and marbling
✕Can appear on preforms and bottles
✓No longer visible
Opacity
✕Needs full dosage
✓Unchanged opacity at lower dosage
Cavity to cavity
✕Variation between cavities
✓Same result in every cavity
Line operation
✕Normal process variability
✓Stabilised operation
✓
Inserts in production. No longevity issues detected; ongoing longevity evaluation with ZEISS CT scanning.

06 · Fitting

Easy to fit in your existing line

GateMix™ sits inside the hot-runner nozzle tip, in the last millimetres before the gate: one insert at each gate. Your team fits it in four steps, with minimum downtime.

Fitting procedure · per gate
1
Remove the nozzle tip

Unscrew the nozzle tip from the nozzle housing. The valve pin stays in place in the hot runner.

2
Place the insert

Slide the GateMix™ insert into the nozzle tip.

3
Slide over the valve pin

Slide the nozzle tip with the GateMix™ insert back over the valve pin. The pin passes through the insert, so the gate shuts off as before.

4
Screw in and restart

Screw the nozzle tip back into the housing and restart production.

Minimum downtime
Same machine and mould
No line modification
Purely mechanical
How we work with you

From first call to your line in three steps

Built around your part, your material and your figures. You decide at every step.

1

Book a discovery call

Tell us about your part, your material and the challenge that matters most. We tell you honestly whether GateMix™ fits.

2

Tune your GateMix™

A technical exchange with your team on your hot-runner configuration, gate and material, so the insert is tuned for your hot runner.

3

Run the trial

We agree the success criteria together and run the trial on your own tool, against a reference without GateMix™. The level of on-site support is agreed with you.

Let’s look at your line together
A free, no-commitment call with our team: tell us about your part, your material and your line, and we tell you whether GateMix™ fits.